manualshive.com logo in svg

Wacker Neuson DV60, Руководство оператора

Поделиться
Скачать
Wacker Neuson DV60 Скачать руководство пользователя страница 116

5-8

BA D24 en/us* 1.0 * D24_1_0_500.fm

 

5 Operation

Operating temperature range

Operate the machine only at ambient temperatures between −15°C (5°F) 
and +45°C (+113°F).

Vehicle travel on slopes

WARNING

Crushing hazard due to tipping over of vehicle!

A tipping vehicle can cause serious injury or death.

► Set the machine to travel position.
► Perform machine travel on slopes only on firm ground.
► Adapt the travel speed to the prevailing conditions.
► Avoid sudden travel movements.
► Pay attention to persons and obstacles.
► Pay attention to the stability limits of the vehicle (maximum gradient 

angle 14° (25%), maximum lateral angle of inclination 14° (25%)).

► Perform uphill and downhill machine travel only in speed range 1.
► Ensure that no parts of the body protrude outside the vehicle.
► Do not exceed the permissible payloads.
► Do not turn or dump out a full skip during uphill or downhill machine 

travel.

► Dump out the skip on slopes only on the uphill side of the machine.
► Diagonal machine travel is prohibited.

Stones and the humidity in the upper layer of the ground can affect vehicle 
traction and stability.
The vehicle can slip sideways on gravel or loose, rocky soil. The stability 
of the vehicle can be reduced on rough terrain.
On soft ground, the machine sinks into it or the wheels dig into it. This 
increases the machine angle (maximum gradient angle and maximum 
lateral angle of inclination), and the machine can tip over.
If the engine dies during uphill or downhill machine travel, immediately put 
the forward-reverse control in neutral position and start the engine again.
The machine can slip even on gentle slopes if it travels across for example 
grass, leaves, humid metal surfaces, frozen ground or ice.

Содержание DV60





















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды