Wacker Neuson DT08 Series Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 102

Wacker Neuson DT08 Series Скачать руководство пользователя страница 52

3-22

BA DT08 SL EN – Edition 1.0 * * dt08b330.fm

Operation

Tying down the machine

Danger!

The machine must be loaded and transported properly –

Danger of accidents!

☞

It is essential that you read the safety instructions at the beginning of this
chapter and follow any other safety instructions relevant in your country!

☞

Ensure that the authorised maximum height is not exceeded

☞

Secure the tracks of the dumper on the sides.

☞

Lower the skip and the loader unit

☞

Firmly fasten the dumper onto the platform. To this end, use chains or straps to pass
the cables between the tracks and the skip

☞

Before transporting the machine through heavy rain:
Cover the exhaust pipe with a suitable cover

☞

Before transporting, ensure that the driver of the transport vehicle knows the overall
height, width and weight of the machine (incl. the dumper) and the applicable legal reg-
ulations in the country where this type of transport is to take place!

Towing the machine

Danger!

Keep out of the danger zone of the machine –

Danger of accidents!

☞

Ensure that no-one is dangerously close to the dumper.

Notice!

The manufacturer’s warranty shall not apply to accidents or damage caused by
towing the machine. No towing away other machines with the eye hook. The
machine can also be salvaged with a crane.

Fig. 55: Tying down the dumper

L1

L2

L2

L1

L2

Fig. 56: Tying down the dumper

«
...
50
51
52
53
54
...
»

Содержание DT08 Series







































































































Отзывы:

Нет отзывов