Wacker Neuson DT08 Series Скачать руководство пользователя страница 49

Страница: 49 / 102

BA DT08 SL EN – Edition 1.0 * dt08b330.fm

3-19

Operation

Parking the machine

Danger!

Always park the machine on firm ground –

Danger of accidents

☞

Park the machine on level ground

☞

Fasten the tracks with fastening elements (e. g. chocks)

☞

Stop the machine

☞

Dump in the skip

☞

Lower the loader unit to the ground

☞

Reduce engine speed completely

☞

Switch off ignition

☞

Remove the ignition key

Caution!

Never stop the engine under full load.

☞

Let the engine run at idling speed for at least 1 minute before switching it
off.

Foothold

Folding up the foothold:

☞

Fold up foothold

with both hands to the upright position.

Folding down the foothold:

☞

Hold foothold

with both hands.

☞

Fold it down to the horizontal position.

Fig. 51: Folding up the foothold

Fig. 52: Folding down the foothold

Содержание DT08 Series







































































































Результаты поиска

Содержание DT08 Series

Отзывы:

Wacker Neuson DT08 Series, Руководство оператора, Страница: 49 / 102

Результаты поиска

Содержание DT08 Series

Отзывы: