Wacker Neuson DT08-D Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 102

Wacker Neuson DT08-D Скачать руководство пользователя страница 51

BA DT08 SL EN – Edition 1.0 * dt08b330.fm

3-21

Operation

Loading and transporting the machine

Safety instructions

• The transport vehicle must be of sufficient size. See

6 “Specifications”

for

the dimensions and the weight of the machine!

• Remove any mud, snow or ice from the tracks so that the machine can be safely driven

onto the ramps

• Secure the machine against unintentional movement

Parking the machine

Danger!

The machine must be loaded and transported properly –

Danger of accidents!

☞

It is essential that you read the safety instructions at the beginning of this
chapter and follow any other safety instructions relevant in your country!

Load as follows:

☞

Secure the transport vehicle with chocks to prevent it from rolling

☞

Place the access ramps at the smallest possible angle. Ensure that the grade does not
exceed 15° (27 %). Use access ramps with an antiskid surface only.

☞

Ensure that the loading area is clear and access to it is not obstructed – e.g. by super-
structures

☞

Ensure that the ramps and the tracks of the dumper are free of oil, grease and ice

☞

Start the engine of the dumper

☞

Lower the skip

☞

Raise the loader unit enough so that it will not touch the access ramps

☞

Carefully drive the dumper onto the middle of the transport vehicle

☞

Lower the loader unit to the loading area

☞

Stop the engine

☞

Remove the ignition key (option)

Notice!

The manufacturer’s warranty shall not apply to accidents or damage caused by
loading or transporting the machine.

<17°

Fig. 54: Access ramps

< 17°

<

«
...
49
50
51
52
53
...
»

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды