manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 33

BA DT08 SL EN – Edition 1.0  * dt08b320.fm

3-3

Operation

10 Alternator charge function indicator light

Caution!

If the indicator light comes on with the engine running:

☞

Stop the engine immediately and

☞

Have the cause repaired by an authorised workshop

The alternator or the charging circuit of the alternator is faulty if the indicator light comes 
on with the engine running. The battery is no longer charged.

11 Engine oil pressure indicator light

Caution!

If the indicator light comes on with the engine running:

☞

Stop the engine immediately and

☞

Check the oil level. If it is too low, fill up the engine oil. If it is correct, contact 
an authorised workshop.

The oil pressure is too low if this indicator light comes on with the engine running. Operat-
ing the machine with insufficient oil pressure can cause engine damage!

13 Buzzer

The buzzer sounds as soon as ignition is switched on.
This avoids emptying the battery by leaving ignition switched on unintentionally.

☞

Turn the ignition key and switch off the control panel.

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды