manualshive.com logo in svg

Wacker Neuson DT08-D, Руководство оператора

Поделиться
Скачать
Wacker Neuson DT08-D Скачать руководство пользователя страница 21

BA DT08 SL EN – Edition 1.0  * dt08b210.fm

2-1

Safety instructions

2 Safety instructions

2.1

Identification of warnings and dangers

Important indications regarding the safety of the staff and the machine are identified in this 
Operator’s Manual with the following terms and symbols:

Danger

!

Failure to observe the instructions identified by this symbol can result in 
personal injury or death for the operator or other persons.

☞

Measures for avoiding danger

Caution!

Failure to observe the instructions identified by this symbol can result in 
damage to the machine.

☞

Measures for avoiding danger for the machine

Notice!

This symbol identifies instructions for a more efficient and economical use of the 
machine.

Environment!

Failure to observe the instructions identified by this symbol can result in damage to the 
environment. The environment is in danger if environmentally hazardous material (e.g. 
waste oil) is not subject to proper use or disposal. 

2.2

Warranty

Warranty claims can be brought forward to your Wacker Neuson dealer only.
Furthermore, the instructions in this Operator’s Manual must be observed.

2.3 Disposal

All fluids, lubricants, material, etc., used on the machine are subject to specific regulations 
regarding collection and disposal. Dispose of different materials and consumables sepa-
rately and in an environmentally friendly manner!
Disposal may be carried out by a Wacker Neuson dealer only. Also observe the national 
regulations regarding disposal!

Environment!

Avoid damage to the environment! Do not allow the oil and oily wastes to get 
into the ground or stretches of water!

Содержание DT08-D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды