Wacker Neuson CRT 48-31V Скачать руководство пользователя | Manualshive

Страница: 39 / 58

background image

CRT 48-31V

Maintenance

wc_tx000142gb.fm

37

5.13 Engine Oil

See Graphic: wc_gr000217

Drain oil while engine is still warm.

5.13.1

Remove oil fill cap

(a)

and drain plug

(b)

to drain oil.

Note:

In the interests of environmental protection, place a plastic sheet

and a container under the machine to collect any liquid which drains
off. Dispose of this liquid in accordance with environmental protection
legislation.

5.13.2

Install drain plug and torque to 34.6 Nm (25.5 ft.lbs.).

5.13.3

Fill engine crankcase with recommended oil until the level is between
“L” and “F” on the dipstick

(c)

.

Oil capacity: 3 l (3.2 qt.).

5.13.4

Install oil fill cap.

5.13.5

To replace the oil filter

(d)

, remove the installed oil filter after oil has

been drained. Apply a thin coat of oil to the rubber gasket of the
replacement oil filter. Screw the filter on until it just contacts the filter
adapter, then turn it an additional ½ turn. Refill with oil as described
above.

«
...
37
38
39
40
41
...
»

Содержание CRT 48-31V



























































Отзывы:

Нет отзывов

Похожие инструкции для CRT 48-31V

RAZORBACK RIDER HD560

Бренд: allen Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды