Wacker Neuson AR Скачать руководство пользователя

Страница: 29 / 62

11 Maintenance

100_0102_mt_0003.fm

11.4

Cleaning the machine

Wacker Neuson recommends cleaning the machine after each use for long, trouble-free running times.

The following points must be observed and complied with:



Do not use high pressure washers for cleaning – danger from electric shock.



Only use clean water for cleaning – wipe machine dry with a cloth.

11.4.1

Cleaning the Bodyguard®



Do not clean the Bodyguard® with high pressure l or steam cleaners!



Do not exert any hammer blows on the Bodyguard® to remove contaminations!



Do not submerge the Bodyguard® in water!



Do not use any fuels or solvents.Explosion hazard!

11.5

Lubricate machine

To achieve long, error-free running times for this machine, Wacker-Neuson recommends lubricating it
periodically.

The following points must be observed and complied with:

1. Remove any dirt around the zerk fitting.
2. Place filled manual lever-type grease gun (DIN 1283) onto the lubrication nipple and operate

approximately once or twice (1.0-2.0 cm3) per lubrication nipple.

3. Wipe the area around the zerk fitting with a clean cloth.

WARNING

Use of improper cleaning agents may lead to fire or explosion.



Do not use gasoline or any other solvents to clean the machine.

WARNING

Excessive grease can conduct electricity.
Injuries from electrocution.



Wipe off excessive grease.

Item

Designation

Tapered zerk fitting

NOTE

Over-greasing alters machine behaviour to the point of failure.

Содержание AR































































Результаты поиска

Содержание AR

Отзывы:

Похожие инструкции для AR

Бренды по названию

Популярные бренды

Wacker Neuson AR, Руководство оператора

Результаты поиска

Содержание AR

Отзывы:

Похожие инструкции для AR

Бренды по названию

Популярные бренды