background image

Page 

17

 of 

19

 

Item – Rev(s):

 9200000150 & 9200000160  – 101 

Inappropriate machine operation may also affect the life of your undercarriage. Take care 
when turning on hard surfaces such as concrete or asphalt. 

 

09 – TROUBLESHOOTING 

Problem 

Possible Causes 

Corrective Action 

Starter does not 
crank engine 

Flat battery 

Charge battery. Replace if required 

Loose/corroded battery connections 

Check connections. Repair or replace as 
required 

Damaged ignition switch 

Test ignition switch. Repair or replace as 
required 

Engine will not start, 
hard to start or fails 
to keep running 

Auxiliary hydraulics lever is engaged 

Disengage the auxiliary hydraulics lever 

Low fuel level 

Add fuel 

Air filter dirty / blocked 

Clean housing and replace filter 

Fuel contamination 

Contact Authorised Dealer for repair 

Engine loses power 

Engine load is excessive 

Reduce ground speed 

Air filter dirty / blocked 

Clean housing and replace filter 

Oil level in engine crankcase is low 

Add engine oil to correct level 

Cooling fins and air passages under 
engine blower housing are blocked 

Remove obstruction from cooling fins 
and air passages 

Fuel contamination 

Contact Authorised Dealer for repair 

Engine overheats 

Engine load is excessive 

Reduce ground speed 

Oil level in engine crankcase is low 

Add engine oil to correct level 

Cooling fins in the radiator are blocked 
or damaged reducing air flow 

Clean or replace radiator as required 

Abnormal vibration 

Engine mounting bolts are loose 

Tighten engine mounting bolts 

Engine mounts are broken 

Replace engine mounts 

Machine does not 
drive 

Hydraulic fluid level low 

Add hydraulic oil to correct level 

Traction pump drive coupler is loose or 
broken 

Contact Authorised Dealer for repair 

Pump and/or wheel motor is defective 
or damaged 

Contact Authorised Dealer for repair 

Control valve is defective or damaged 

Contact Authorised Dealer for repair 

Relief valve is defective or damaged 

Contact Authorised Dealer for repair 

 

 

 

 

Содержание 9200000150




















Отзывы: