Wacker Neuson 0008060 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

Wacker Neuson 0008060 Скачать руководство пользователя страница 32

Maintenance

WP 1540A/AW

wpm_tx001130gb.fm

30

5.9

Cleaning Sediment Cup

See Graphic: wc_gr000029

5.9.1

Turn the fuel valve off.

5.9.2

Remove the sediment cup

(a)

and the O-ring

(b)

.

5.9.3

Wash both thoroughly in a nonflammable solvent. Dry and reinstall
them.

5.9.4

Turn the fuel valve on and check for leaks.

5.10 Adjusting Engine Speed

See Graphic: wc_gr000280

Adjust to a full load speed of 3600 ± 100 rpm.
To adjust engine speed:

5.10.1 Place machine on a rubber test mat to prevent it from moving.
5.10.2 Start engine and allow it to warm up for a minute.
5.10.3 Turn throttle stop screw

(a)

in to increase speed, out to decrease

speed. Make sure throttle lever is touching stop screw before
measuring RPM.

NOTICE

:

Running plate at a speed higher than that listed in

Technical

Data

can damage both the plate and the engine.

wc_gr000280

a

«
...
30
31
32
33
34
...
»

Содержание 0008060











































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды