Vulcan-Hart ML-126610 страница 22 Скачать руководство пользователя

Страница: 22 / 75

INTERIOR LIGHTS

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Lamp

Remove the racks.

Unscrew the glass lens for the light being
replaced then unscrew the bulb.

Fig. 50

Replace bulb then reverse the procedure to
install.

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Lamp Assembly

Remove the lens and bulb.

Remove the springs from the retaining tabs (2
places) on the socket.

Fig. 51

Depress the retaining tabs and pull the socket out
from the oven, far enough to disconnect the lead
wires.

Remove the socket from the oven.

Attach the lead wires to the replacement socket.

Insert the socket into the hole in the oven and
push until the socket is held in place by the
retaining tabs.

Install the light bulb and lens.

Check for proper operation.

COOLING FAN

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Remove the Right Side Panel.

NOTE:

If right side panel is not accessible, this

component can be serviced by removing the Control
Panel.

Disconnect the lead wires to the fan motor by
removing wire nuts.

Remove the screws securing the air deflector to
the fan then loosen the tab screw holding the fan
to the component panel. Rotate the tab so that
the fan will clear and remove the fan.

Fig. 52

Reverse the procedure to install the replacement
fan and check for proper operation.

VC4G & VC6G SERIES FULL SIZE CONVECTION OVENS - REMOVAL AND REPLACEMENT OF PARTS

F24682 Rev. D (1016)

Page 22 of 75

Содержание ML-126610












































































Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды

Vulcan-Hart ML-126610, Руководство по обслуживанию

Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды