Quick start guide
FS6220-2/FS6220-3/FS6224/
FS6224-2/FS6224-21/FS6224-3
Introduction
This quick start guide provides you with the basic installation
and setup instructions. A limited set of features are
described in abbreviated form.
You may refer to the Abridged user’s manual provided in the
product package for installation and operation instructions,
or see the online Complete user’s manual at
www.vtechphones.com for complete installation and
operation instructions.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Plug the battery connector
securely into the socket.
1.
Place the battery with the
label
THIS SIDE UP
facing
up and the wires inside the
battery compartment.
2.
Slide the battery
compartment cover towards
the center of the handset
until it clicks into place.
3.
Place the handset in the
telephone base or charger
to charge.
4.
Enter the handset menu
Press
MENU
.
Press
or until the screen
displays the desired feature menu.
Press
SELECT
.
To return to the previous menu,
press
CANCEL.
To return to idle mode,
press and hold
CANCEL.
1.
2.
3.
•
•
Set date and time
Press
MENU
.
Scroll to
Settings
then press
SELECT
.
Scroll to
Set date/time
, then press
SELECT
.
Use the dialing keys (
0
-
9
) to enter the month, date and year
and then press
SELECT
.
Use the dialing keys (
0
-
9
) to enter the hour and minute.
Press or to select
AM
or
PM
.
Press
SELECT
.
Set number of rings
You can set the answering system to answer an incoming call
after two, three, four, five or six rings; or toll saver. With toll
saver selected, the answering system answers after two rings
when you have new messages, or after four rings when you
have no new messages.
Press
MENU
.
Scroll to
Answering sys
, then press
SELECT
.
Scroll to
Ans sys setup
, then press
SELECT
.
Scroll to
# of rings
, then press
SELECT
.
Press or to choose
6
,
5
,
4
,
3
,
2
or
Toll saver
,
then press
SELECT
.
Record your own announcement
You can use the preset announcement to answer calls,
or replace it with your own recorded announcement. The
announcement can be up to 90 seconds in length.
Press
MENU
.
Scroll to
Answering sys
, then press
SELECT
twice.
Press
7
to record.
Speak towards the microphone after the handset announces,
“
Record after the tone. Press
5
when you are done
.”
Press
5
when finished.
IMPORTANT!
Refer to the online Complete user’s manual for a full set of
installation and operation instructions. For manual download or
customer service, visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
Copyright © 2012 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
96-008452-030-100
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
Battery installation and charging
Install the battery as shown below. Once you have installed the
battery, you may be able to make and receive short calls. For best
performance, charge the handset battery continuously for at least
12 hours.
Telephone
wall jack
Telephone
line cord
Electrical
outlet (not
controlled
by a wall
switch)
Telephone
base power
adapter
Charger
adapter
Telephone base
Charger
Use only the power adapter(s) and battery(ies) supplied
with this product.
A DSL filter
(not included) is
required if you
have DSL
high-speed
Internet service.
The DSL
filter must be
plugged into
the telephone
wall jack.
Press to
scroll down
Press to
scroll up
