Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This user’s manual has instructions on how
to set up and register your new emergency
button. For instructions on using the
emergency button, see the quick start
guide or the online complete user’s manual
of your telephone base.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com
. In Canada, visit
www.vtechcanada.com
.
What’s in the box
Your emergency button package contains
the following items. Save your sales
receipt and original packaging in the event
warranty service is necessary.
To deregister all devices from the telephone
base:
1. Press and hold
PAGE
on the telephone
base for about five seconds until the
visual indicator light on the telephone
base turns on. Keep holding
PAGE
until
the visual ringer indicator light begins to
flash. Release
PAGE
.
2. Immediately press
PAGE
again while the
light is still flashing.
You hear a confirmation tone when the
deregistration process completes. It
takes about 10 seconds to complete the
deregistration.
Operating range
The operating range of the emergency
button is up to 1,000 feet outdoors or 150
feet indoors. The actual operating range
may vary depending on the environmental
conditions and other interferences such as
walls, doors and other obstructions.
Test the signal strength
You can carry your emergency button as
you walk around your home.
Follow the instructions below to check the
signal strength between the emergency
button and the telephone base.
Test device signal strength with your
SN5127/SN5147 telephone
1. Press
MENU
on the cordless handset
when the telephone is not in use.
2. Press or to scroll to
Device setup
,
and then press
SELECT
.
3. Press
SELECT
to select
Check signal
.
4. Scroll to select
Emergency button
, and
then press
SELECT
.
5. When the handset screen displays
PLS
TRIGGER THE DEVICE
, make sure your
emergency button is powered on, and
then press
SELECT
.
6. The handset screen displays
AWAITING
SIGNAL
.
• If the handset screen displays
NO
SIGNAL
, press
SELECT
, and then
repeat from step 2 to test again.
• If the handset screen displays
WEAK
SIGNAL
, move the emergency button
closer to the base, and then adjust
the emergency button’s position to
improve the signal. Press
SELECT
, and
then repeat from step 2 to test again.
7. When the handset screen displays
GOOD
, press
SELECT
. The testing is
complete.
Portable use of emergency button
1. Open the lock and insert one end of
the lanyard into the slot on top of the
emergency button.
2. Close the lock.
For detailed operations, read the
SOS emergency call
section in the quick
start guide or the online complete user’s
manual of your telephone system.
User’s
manual
Emergency button overview
1 – LED (red)
• Steady on when in emergency
mode after the emergency key is
pressed.
• Flashes when registering to the
telephone base.
• Flashes slowly when the emergency
button is out of range of the
telephone base.
2 –
Emergency key
• Press to enter emergency mode and
automatically dial the emergency
numbers preset in the telephone
base.
3 – Slot for portable use
4
– CANCEL (PAIR)
• Press to cancel emergency call
mode.
• Press and hold to enter pairing
mode.
5 – Battery compartment cover
6 – Screw
• Unscrew it to open the battery
compartment cover.
• Tighten it to close the battery
compartment cover.
Lanyard overview
1 – Move button
• Press and adjust the button position
for wearing comfort.
2 – Lock
• Open and insert the lanyard into the
slot on top of the emergency button.
Install the battery
Install battery
Notes
• Use only supplied battery or equivalent.
• If the emergency button will not be used
for a long time, disconnect and remove the
battery to prevent possible leakage.
1. Insert the supplied battery into the
battery compartment, and matching the
polarity markings (+ and -) inside it.
2. Close the battery compartment cover.
3. Use a screwdriver to tighten the screw to
secure the battery compartment cover
in place.
CAUTIONS
CAUTION
Caution
• Your emergency button is water spray
resistant. Make sure the battery compartment
cover is tightly closed and the screw is
tightened to prevent water spray from
penetrating.
Replace battery
With average use, your emergency
button’s battery should last approximately
two years. When the battery is low, replace
it with a new CR123A Lithium battery.
1. Use a screwdriver to loosen the screw on
the battery compartment cover.
2. Flip open the battery compartment
cover and take out the old battery.
3. Follow the steps in
Install battery
to
install a new battery to the Emergency
button.
Before use
Add and register a handset
Register each new
SN7022
Emergency
button to your CareLine® telephone
base (
SN5127
/
SN5147
) before use. Your
telephone system supports a maximum
of four handsets and 30 compatible ULE
devices.
Notes
• Install the battery before registering it to the
telephone base.
• Visit
www.vtechphones.com
for a list of
ULE devices that are compatible with your
CareLine telephone base
SN5127
/
SN5147
.
To register an emergency button to
the SN5127 telephone base:
Install the batteries before registering it to
the telephone base.
1. When the telephone is not in use,
press and hold
PAGE
at the telephone
base for about five seconds until the
visual ringer indicator light turns on.
Release
PAGE
.
2. Press and hold
CANCEL
on the back of
the emergency button until the red LED
light flashes, then release
CANCEL
.
It takes up to 60 seconds to complete
the registration. When the registration
is successful, the red LED lights on the
emergency button turns off, and the
telephone base beeps and its visual ringer
indicator light turns off.
If registration fails, start again from Step 1
above.
Notes
• You cannot register an emergency button if
any other system device is in use.
To register an emergency button to
the SN5147 telephone base:
Install the batteries before registering it to
the telephone base.
1. When the telephone is not in use,
Press and hold
at the telephone
base for about five seconds until the
visual ringer indicator light turns on.
Release
.
2. Press and hold
CANCEL
on the back of
the emergency button until the red LED
light flashes, then release
CANCEL
.
It takes up to 60 seconds to complete
the registration. When the registration
is successful, the red LED lights on the
emergency button turns off, and the
telephone base beeps and its visual ringer
indicator light turns off.
If registration fails, start again from Step 1
above.
Notes
• You cannot register an emergency button if
any other system device is in use.
Replace an emergency button
If you have purchased this new
SN7022
accessory emergency button to replace
an old one, you must deregister the old
emergency button first, and then register
this new emergency button to your
CareLine telephone base (
SN5127
/
SN5147
).
Deregister an emergency button
If you want to replace an emergency
button, you must deregister all the devices,
and then individually register each device.
If you want to register an emergency
button to another telephone base, you
must deregister all devices, and then
register each device individually to the
desired telephone base.
1
2
3
4
1
2
4
6
3
5
SN7022
VTech CareLine®
Wearable home SOS pendant
for use with SN5127/SN5147
telephone system
Go to
www.vtechphones.com
to register your product for enhanced
warranty support and latest VTech
product news
User’s manual
SN5127 base
SN5147 base
1
2
