manualshive.com logo in svg

VRmagic Eyesi, Инструкция по установке и эксплуатации, Страница: 30 / 80

Поделиться
Скачать
VRmagic Eyesi Скачать руководство пользователя страница 30

4.10 Checking the Voltage Settings  

(applies only to lifting columns of type TES2)

Info 

Check identification plate

This section only applies to lifting columns of type TES2. If your simulator is 
equipped with a lifting column of type TAOP, please skip this section.

The type of your lifting column can be read from the identification plate at the 
lower rear side.

As a factory preset, the voltage setting is already adjusted to the power supply volt-
age in your country. However, always check the voltage setting before you connect 
the simulator to a power source.

Checking the voltage setting:

1. 

Take a look at the power inlet at the bottom of the lifting column (

Â

 see follow-

ing figure).

 

▷

Above the 3-pin socket there is a voltage selector switch.

1  

Voltage selector switch

2  

Currently set voltage

3  

Power inlet

4  

3-pin socket

Fig. 19: Power connector with voltage selector switch

2. 

Check the voltage displayed on the voltage selector switch. 

 

▷

The displayed voltage has to match the power supply voltage in your 
country.

 

▷

If a wrong voltage is preset, adjust the voltage setting according to the fol-
lowing instructions.

Eyesi Surgical Simulator – Installation and Operating Guide

30

Installation

Содержание Eyesi

















































































Отзывы:

Нет отзывов