manualshive.com logo in svg

VRmagic Eyesi, Инструкция по установке и эксплуатации, Страница: 20 / 80

Поделиться
Скачать
VRmagic Eyesi Скачать руководство пользователя страница 20

4. 

Move the operating table so that the two screws are pushed into the matching 
slots of the lifting column (

Â

 see following figure).

Fig. 3: Place the table on the lifting column and push the two screws into the matching slots of the 
lifting column

5. 

Verify that no cables have become kinked or otherwise damaged.

6. 

Insert two M6 x 25 mm screws into the remaining holes of the lifting column’s 
mounting plate and tighten them slightly. You might need to gently shift the 
operating table around to align the holes of the two mounting plates properly 
(

Â

 see following figure).

Fig. 4: Inserting the remaining screws into the  
mounting plate

7. 

Tighten all four M6 x 25 mm screws by hand with the 5 mm hexagon key until 
they are firm.

Electrically connecting the lifting column to the operating table:

There is a connection cable with a round plug located at the top of the lifting column. 
The cable is used for height adjustment of the operating table.

1. 

Connect the cable with the round plug to the matching jack located underneath 
the operating table.

Eyesi Surgical Simulator – Installation and Operating Guide

20

Installation

Содержание Eyesi

















































































Отзывы:

Нет отзывов