VRmagic Eyesi Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 80

VRmagic Eyesi Скачать руководство пользователя страница 11

This product must be connected to a 15 A branch circuit only. Only use the supplied
power cable to connect the simulator to the mains power supply. If the supplied
power cable is damaged, contact VRmagic to order a new one.

2.9 Operation

Simulator

Only switch on the simulator if the simulator temperature and the room temperature
range between 10–30 °C (50–86 °F).

The power inlet of the simulator is located at the base of the lifting column near the
floor. Make sure that water never comes into contact with the power inlet. Advise
cleaning personnel to be especially careful while wet mopping the floor near the
simulator. It has to be made sure that the floor is not left even slightly wet near the
power inlet. Otherwise electric shock hazard or device damage may occur.

Remove the power plug immediately if liquid enters any part of the enclosure. In
this case, the equipment needs to be checked by VRmagic or an authorized service
technician.

When opening the housing of any of the simulator components while the system
is connected to power, there is the risk of death or serious injury through electrical
shock. Further, the simulator might get damaged and the warranty will be voided.
Never attempt to open the housing of any of the components.

Do not place objects on the simulator PC.

In the event of failure, or if safe operation of the simulator or any device connected
to it cannot be assured, the simulator must be taken out of operation and must be
secured against unintentional activation or use. Disconnect the power plug from
the power source immediately. Ask VRmagic or an authorized service technician to
check the device.

Safe operation is not assured

• if the voltage requirements of the simulator do not match the power supply

voltage.

• if any part of the simulator or a cable is visibly damaged.

• if the simulator is not operating properly.

• if the simulator has been exposed to rain or other wet conditions.

• if liquid or objects have entered any part of the simulator.

• after storage under adverse conditions.

• after heavy strain in transporting the device.

11

Safety

Eyesi Surgical Simulator – Installation and Operating Guide

«
...
9
10
11
12
13
...
»

Содержание Eyesi

















































































Отзывы:

Нет отзывов