VQ VQA05 Tuskegee Скачать руководство пользователя страница 1

474976

“TUSKEGEE”

Airman

NORTH AMERICAN

SPECIFICATIONS

Wingspan                                       1580mm
Length                                            1180mm
Electric Motor                                870 Watt 
Glow Engine                       .46 2-T / .70 4-T
Radio                    4-5 Channel / 4-5 Servos

TECHNISCHE DATEN

Spannweiter                                   1580mm
Lange                                             1180mm
Elektroantrieb                                870 Watt 
Verbrennerantrieb        7.5cc 2-T / 11cc 4-T
Fernsteuerung         4-5 Kanal / 4-5 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

46 Class

70 Class

(2T Engine)

(4T Engine)

Instruction manual / Montageanleitung

Or Electric equivalent

RADIO CONTROL MODEL / RC FLUGMODELL

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

VQA06 “Shangri-la”

VQA05 “Tuskegee”

Содержание VQA05 Tuskegee
















Отзывы: