VQ Model TOMHAWK Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 13

VQ Model TOMHAWK Скачать руководство пользователя страница 1

Sport “ JET”

VQA023

SPECIFICATIONS

Wingspan 1372mm
Electric Motor 870 Watt (PULSAR 60)
Glow Engine 46 2-T
Radio 4 Channel / 4 Servos

TECHNISCHE DATEN

Spannweite 1372mm
Elektroantrieb 870 Watt (PULSAR 60)
Verbrennerantrieb 7.5cc 2-T
Fernsteuerung 4 Kanal / 4 Servos

Instruction manual / Montageanleitung

RADIO CONTROL MODEL / RC FLUGMODELL

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

WARNING!

This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG!

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

1
2
3
...
»

Содержание TOMHAWK














Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды