Vox VTX150 neodymium Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 44

background image

8

AMP LED

AMP selector

AMP switch

3. AMP section

Here you can adjust the settings for the amp using
the traditional VOX “chicken head” knobs.

AMP switch and selector, LED

Here you can select the amp mode.
Each time you press the AMP switch, the bank and
AMP LED color will change as follows:
• STD (Standard): green
• SPL (Special): orange
• CST (Custom): red
• EXT (Extra): blue
Use the AMP selector to choose a model within the selected amp bank.
The operation of the gain circuit, and the response of the tone controls and
their location within the circuit are all switched according to the amp model
that you select here.
In Preset mode (i.e., when the PRESET LED is lit-up), you can recall preset
programs that contain sounds and effect settings that are typical of each amp
model.

GAIN control

This adjusts the pre-amp gain of the selected amp model.

VOLUME control

This adjusts the volume of the selected amp model.

TREBLE, MIDDLE, BASS controls

These adjust the tone for the high, mid, and low-frequency ranges. The
changes that are produced by each control will differ depending on the amp
model that you’ve selected.

MASTER volume

This adjusts the volume that is output from the pre-amp to the Valve Reactor
power amp. This setting will change the amount of the Valve Reactor’s distor-
tion.

NOTE:

The MASTER volume setting is not programmed.

NOTE:

The amount of Valve Reactor distortion is also affected by the

GAIN control and VOLUME control. With some settings, there will be
almost no distortion.

«
...
6
7
8
9
10
...
»

Содержание VTX150 neodymium













































Отзывы:

Нет отзывов

Похожие инструкции для VTX150 neodymium

Бренд: Datavideo Страницы: 8

Бренд: Atlona Страницы: 9

Бренд: Waterfall Audio Страницы: 34

Бренд: XINDAK Страницы: 10

Бренд: Kramer Страницы: 26

Бренд: Cary Audio Design Страницы: 20

Бренд: Balanced Audio Technology Страницы: 9

Бренд: PowerBass Страницы: 28

Бренд: Goldmund Страницы: 14

Бренд: Chord Electronics Страницы: 29

Бренд: IRF Страницы: 50

Бренд: Harley Benton Страницы: 28

Бренд: MAG THEATRON Страницы: 28

Бренд: B&K Страницы: 16

Бренд: T&M Performance Страницы: 8

Бренд: Altronics Страницы: 4

Бренд: Alpine Страницы: 16

Бренд: HZ Sound Systems Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды