Vox VTX150 neodymium Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 44

background image

36

Troubleshooting

1. Power does not turn on when you turn the

POWER switch on

• Is the power cable connected to the rear panel AC power inlet?
• Is the power cable connected to an AC outlet?
• Could the AC outlet be malfunctioning?
• Could the power cable be damaged?

2. No sound from the amp

• Could your guitar’s volume be turned down?
• Is your guitar cable connected correctly?
• Could your guitar cable be broken?
• Could the top panel MASTER volume be turned down?
• Could headphones be connected to the top panel PHONES jack? If so, discon-

nect them.

• Check the settings of the GAIN, VOLUME, TREBLE, MIDDLE, and BASS

controls. For some amp models, there may be no sound from the amp if the
TREBLE, MIDDLE, and BASS controls are turned down, just as for the cir-
cuitry of the original amp.

• If the VTX150 Neodymium is in Manual mode (MANUAL LED lit), could the

GAIN, VOLUME, TREBLE, MIDDLE, and BASS controls be set to 0 or the
minimum value?

• Could the VOLUME pedal of a VC-12SV connected to the VTX150 Neody-

mium be set to the minimum position? Alternatively, could the expression
target be set to the GAIN parameter of the amp or pedal effect, with the
expression pedal set to the minimum position?

3. Insufficient volume from the amp

• Could your guitar’s volume be turned down?
• Could the MASTER volume be turned down?
• Could the POWER LEVEL be turned down?
• Could a high impedance speaker (e.g., 16 ohms) be connected to the EXTEN-

SION SP jack?

• Check the settings of the GAIN, VOLUME, TREBLE, MIDDLE, and BASS

controls. For some amp models, there may be no sound from the amp if the
TREBLE, MIDDLE, and BASS controls are turned down, just as for the cir-
cuitry of the original amp.

• If the VTX150 Neodymium is in Manual mode (MANUAL LED lit), could the

GAIN, VOLUME, TREBLE, MIDDLE, and BASS controls be set to 0 or the
minimum value?

«
...
34
35
36
37
38
...
»

Содержание VTX150 neodymium













































Отзывы:

Нет отзывов

Похожие инструкции для VTX150 neodymium

Бренд: Barcus-Berry Страницы: 2

Бренд: D.A.S. Страницы: 11

Бренд: TEC Страницы: 15

Go Wireless Series

Бренд: Vernier Страницы: 3

SU-Z65 - SERVICE

Бренд: Technics Страницы: 20

Бренд: Technics Страницы: 100

Бренд: rauland Страницы: 10

Le Preamp Series

Бренд: Two Notes Страницы: 21

Бренд: Ultrasound Страницы: 2

Бренд: RE Audio Страницы: 12

Бренд: Fender Страницы: 18

Бренд: DAPAudio Страницы: 14

Бренд: Talk electronics Страницы: 7

Бренд: ATI Audio Страницы: 14

Бренд: Altronics Страницы: 4

Бренд: Decware Страницы: 18

Full Tube Guitar Amplifier

Бренд: Engl Страницы: 28

Бренд: PJB Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды