Volvo SDLG LG936L Скачать руководство пользователя страница 81

Страница: 81 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

than 70% of the maximum speed limit.

Pay attention to the lubricating condition; routinely add and change the lubricant according to

rules.

Pay attention to the temperatures of the gearbox, torque converter, front and rear frame, rim and

brake drum. Once they are overheating, find the reason and repair it.

Check the fastening conditions of the bolts and nuts.

Do the following maintenance after 10 hours of run-in time on the new loader:

Check the fastening status of bolts and nuts of all parts, but especially the bolts of diesel engine

cylinder cover, vent-pipe bolts, front and rear frame bolts, rim bolts, transmission axle bolts and

connection bolts.

Clean the raw and essential engine oil filter and fuel filter.

Check the tension status of the belts of fan, electrical machine and air condition compressor

Check the capacity of the storage battery electrolyte and its reserves, and fasten the connect

poles.

Check the oil level of the gearbox. Please refer to

3.6.3 Adding Oil to Gearbox

in this

chapter.

Check the seal of the hydraulic system and braking system.

Check the connection and sensitivity of all control levers.

Check the temperature and the connections of the circuit system, the power supply of electrical

machine, gauge, light and lamps and turning signals.

Open the air storage tank to drain water.

The following maintenance should be done after the run-in period of new machine:

Clean the filter at the bottom of the gearbox and the oil filter cartridge of the torque converter.

Check the oil returning filter cartridge of the hydraulic oil tank.

Change the engine oil. Please refer to

3.6.1 Fuel Supplying of Engine

in this chapter.

3 OPERATION AND USE OF LOADER

3.1 Notices for Usage

The diesel must be cleaned and deposited more than 72 hours before it is to be used. The

trademark should suit the rules.

Transmission oil for the gearbox, torque converter, and the hydraulic oil for hydraulic system

must be clean.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды