Volvo SDLG LG936L Скачать руководство пользователя страница 80

Страница: 80 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

headrest.

1.2.11 Use of Safety Belt

If the safety belt is assembled on the seat, please tie it when operating the machine. Before using

safety belt, please check the degree of wear and firm. Replace it if it is necessary.

Adjust the length of safety belt before using to make sure the safety belt can be used for safety

guarantee and comfort. Move the position of lock on the safety belt to adjust the length of safety belt.

The clamper of the safety belt is at the right side of seat, and put the lock into the opening of clamper

to jam the lock. There is a red button on the side of opening of clamper. Press the button and the lock

will jump out from the clamper. Before using the safety belt, please check the clamper of safety belt

whether lock and loose normally.

1.2.12 Rearview Mirror

Rearview mirrors are on the left and right sides outside the cab and left upper inside the cab. Before

starting work, the rearview mirror must angle be adjusted for a good rear.

1.2.13 Key

This loader equips two key for every using condition:

The key of left and right doors of cab.

The starting switch key for engine.

The key of left and right doors of engine hood.

The key of left and right otter boards of engine hood.

The key for adding fuel port of fuel box.

2 RUN-IN PERIOD OF NEW MACHINE

A new machine must have a run-in period first to increase the load step by step from free rotating; so

that each part of the machine can be have full run-in period for increasing the life of the machine. It

needs 60 hours to train the new machine, and operate follows:

Run the machine in neutral at low-speed to preheat the engine.

Never accelerate the engine suddenly in the preheating period.

Never start, accelerate, turn or brake suddenly except in an emergency.

When the loader is working without a load, the gearshift should be used from low speed to high

speed at each level accordingly. Turn left, right or brake steadily in the process of driving.

In the period of run-in, all speeds including forward and reverse should be adjusted.

It is better to load bulk materials in the period of run-in. Do not operate the loader too hard or too

rudely. The load should be less than 70% of the standard load, and the speed should be better less

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды