Volvo SDLG LG936L Скачать руководство пользователя страница 109

Страница: 109 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

CHAPTER

MAINTENANCE

Ⅳ

1 MAINTENANCE GUIDE

Read following information carefully before carrying out maintenance and inspection.

1.1 Attention to Maintenance and Inspection

Perform the maintenance on hard and level ground.

Lower the work equipment near the ground and level the bucket.

Set all control levers (or handles) to the

Neutral

position.

Press the parking brake switch.

Put blocks in the front and back of wheels.

Lock the front and rear frames with frame locking bars.

1.2 Hanging Warning Tag

Attach the warning tag near the starting switch before maintenance to prevent someone starting

the engine during maintenance.

1.3 Fitting preparation

Use only parts specified by the manufacturer of the loaders wheel.

1.4 Oil and Fuel preparation

Use oil and fuel specified in this manual according to ambient temperature.

1.5 Using the Prescriptive Oil and Fuel

Keep containers of oil and fuel clean and use clean oil and fuel.

1.6 Keep the Machine Clean

Always

keep the machine clean. Keep grease fittings, pipe joints and oil level gauges clean and

prevent foreign materials entering.

1.7 Pay Attention to the Refrigerant Water and Oil in High Temperature

It is very dangerous to drain hot oil and refrigerant water or remove the filters immediately after

the engine stops. Make sure the engine is cool. The temperature of the oil drained is appropriately

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды