Volvo Penta TAD1340VE Скачать руководство пользователя страница 94

Страница: 94 / 106

Lubrication System

Oil change volume, including filter change

Composite sump (Standard)

48 liters (12.68 US gal)

Aluminum sump (Optional)

55 liters (14.53 US gal)

TAD1650VE (Aluminum sump, Standard)

55 liters (14.53 US gal)

Additional volume:
Remote oil filters (Optional)

3 liters (0.80 US gal)

Oil pressure, hot engine

at operating speed

300-650 kPa (44–94 psi)

TAD1650VE

400–650 kPa (58–94 psi)

Oil filter

Full flow filter

By-pass filter

Lube oil pump

Type

Gear driven

Oil recommendations

Type designation

Oil quality

Oil change interval, reached first in

operation:

TAD1640GE-B, TAD1641GE-B,
TAD1642GE-B, TWD1643GE,
TWD1644GE, TWD1645GE, TAD1650GE,
TAD1651GE, TWD1652GE, TWD1653GE
TAD1640VE-B, TAD1641VE-B,
TAD1642VE-B, TAD1643VE, TAD1650VE

VDS-3
VDS-2

600

hours or 12 months

TAD1650VE-B, TAD1651VE
TAD1643VE-B

VDS-3
VDS-4.5

500

hours or 12 months

VDS = Volvo Drain Specification

Viscosity

Select the viscosity according to the table.

The temperature values refer to stable ambient
temperatures.

* SAE 5W/30 refers to synthetic or semi-synthetic oils.

Technical Data

47711296 01-2019 © AB VOLVO PENTA

Содержание TAD1340VE











































































































Результаты поиска

Содержание TAD1340VE

Отзывы:

Похожие инструкции для TAD1340VE

Бренды по названию

Популярные бренды

Volvo Penta TAD1340VE, Руководство оператора

Результаты поиска

Содержание TAD1340VE

Отзывы:

Похожие инструкции для TAD1340VE

Бренды по названию

Популярные бренды