Volvo Penta D7A T Скачать руководство пользователя страница 86

Страница: 86 / 116

Raw water pump

Disassembly

1 Drain the water from theraw water system.

2 Remove the coolant pipes to and from the raw

water pump.

3 Remove the connecting socket.

4 Remove the screw cap.

5 Remove the hex nut from the gear.

6 Remove bolts.

7 Remove gear from shaft by using an arbor.

NOTICE!

In order not to damage the shaft when

removing the gear, the hex nut must be flush with the
shaft of the raw water pump.

Assembly

IMPORTANT!

Always use new gaskets and Orings.

1 Install the pump with a new gasket.

2 Fit the gear with a new hex nut, tighten to 80 Nm,

Pay attention that the key is fitted.

NOTICE!

The cones of the gear and shaft must be free

from lubricant, clean and undamaged.

3 Fit the screw cap with a new O-ring.

4 Fit the connecting socket with a new gasket.

5 Install the coolant pipes to and from the raw water

pump.

P0003674

P0003734

P0003736

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды