Volvo Penta D7A T Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 116

background image

Starting Using Auxiliary Batteries

WARNING!

Explosion hazard. Batteries contain and give off an
explosive gas which is highly flammable and explosive.
A short circuit, open flame or spark could cause a
violent explosion. Ventilate well.

Never reverse the polarity of the battery. Risk of sparks
and explosion.

1 Make sure the rated voltage of the auxiliary battery

is the same as the system voltage of the engine.

2 Connect the red auxiliary cable to the discharged

battery’s + terminal and then to the auxiliary
battery’s + terminal.

3 Connect the black jump lead to the auxiliary battery

negative terminal and then to a position slightly
away from the discharged batteries, for example at
the negative cable’s connection to the starter
motor.

WARNING!

The black auxiliary cable (–) must not come in
contact with the positive connection on the starter
motor.

4 Start the engine and run at no load for about ten

minutes to charge the batteries.

WARNING!

Do not touch the connections while attempting to
start; Risk of sparks. Do not bend over the batteries
either.

5 Stop the engine. Remove the auxiliary cables in

reverse order to connecting.

Starting

47713337 03-2021 © AB VOLVO PENTA

23

«
...
23
24
25
26
27
...
»

Содержание D7A T





















































































































Отзывы:

Нет отзывов

Похожие инструкции для D7A T

Univerge SV8100

Бренд: NEC Страницы: 3

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: Quickmill Страницы: 3

Бренд: NEC Страницы: 146

Бренд: Laars Страницы: 28

M16/RM N.C. DN 65 EEX

Бренд: Madas Страницы: 44

Бренд: Neets Страницы: 12

Бренд: National Instruments Страницы: 24

Бренд: Parkside Страницы: 65

Бренд: Polycom Страницы: 2

Бренд: DigiPower Страницы: 27

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

BIS U-830-4-011-H-1

Бренд: Balluff Страницы: 2

Бренд: Aqua Lung Страницы: 24

Бренд: Widex Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды