Volvo Penta D16 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 90

background image

Warranty

Your new Volvo Penta marine engine is covered by a
limited warranty, subject to the conditions compiled in
the Warranty Information. Note that AB Volvo Penta’s
liability is limited to the specification in the Warranty
Information and Emission Control System Warranty
Statement.

Volvo Penta warranty terms and conditions can be
found via http://manual.volvopenta.com/coupon/. Use
the publication number (at the bottom of each page) of
this the manual as reference number.

Read the information carefully, as soon as possible
after delivery. It includes important information about
service and maintenance; the owner is responsible for
being familiar with, checking and implementing these.
Otherwise AB Volvo Penta may deny its warranty
obligations in part or in full.

NOTICE!

Make sure that a Commissioning has been

carried out on your Volvo Penta engine. This should be
done together with your Volvo Penta dealer when
finalizing the purchase. Without a proper
Commissioning registration the warranty will not be
valid.

Contact your Volvo Penta dealer if you have not
received the Warranty Information or Service
Book.

Running in the engine

The engine must be run in during the first 10 hours of
operation. Do this by using the engine in normal
operation, where full load is only applied for short
periods of time. Never run the engine at constant
speed for any longer periods of time.

Since oil consumption is higher during the running in
period, be sure to control the oil level more frequently
than normally recommended. See

Maintenance

for

more information.

Fuel, oils and coolant

Only use the fuels and oils recommended in the
Operator’s Manual, other viscosity and quality may
cause malfunctions, increased fuel consumption and
possibly shorten the life of the engine.

Always change the oil, oil filters and fuel filters at the
specified maintenance intervals.

Make sure to always use suitable and correctly mixed
coolant.

If an unsuitable coolant has been used, or if the
instructions for coolant mixture have not been
followed, future warranty claims related to engine and
accessories may be denied.

Introduction

14

47711740 05-2019 © AB VOLVO PENTA

«
...
14
15
16
17
18
...
»

Содержание D16



























































































Отзывы:

Нет отзывов

Похожие инструкции для D16

Бренд: Daspi Страницы: 40

MICROPUMP DEELE

Бренд: Idex Страницы: 23

Бренд: ebm-papst Страницы: 9

Бренд: ABB Страницы: 215

EMMS-ST-28-L Series

Бренд: Festo Страницы: 4

Бренд: Forest-Master Страницы: 16

Бренд: Habasit Страницы: 60

Бренд: Honda Страницы: 2

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: O.S. engine Страницы: 21

max-12TZ series

Бренд: O.S. engine Страницы: 41

Бренд: Honda Страницы: 193

Бренд: Sonny's Страницы: 15

V-Green Green Choice

Бренд: A.O. Smith Страницы: 8

Бренд: Grundfos Страницы: 24

Parilla Leopard K

Бренд: IAME Страницы: 46

Бренд: DAF Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды