Volvo Penta D1 Series Скачать руководство пользователя страница 56

Страница: 56 / 92

Idling

For engine idle revolutions, refer to the

Engines

section. Low idle revolutions may cause the engine to
stall, while higher idle revolutions cause extra stress
on the drive/reverse gear during shifting maneuvers.

Adjustment must be made while the engine is warm.

1 Put the control lever in neutral.

Check that the gap (A) is around 3 mm.
Undo locknut (B) and adjust screw (C) to give the
correct gap. Tighten the locknut.

(1)

2 Start the engine and let it idle with the control lever

in the neutral position.

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

3 Undo the locknut (D). Adjust to the correct

revolutions using the adjuster screw (E). Tighten
the lock nut.

4 Repeat item 1.

1. This item does not apply to boats with twin helm stations.

Maintenance

47711262 01-2019 © AB VOLVO PENTA

Содержание D1 Series





























































































Результаты поиска

Содержание D1 Series

Отзывы:

Похожие инструкции для D1 Series

Бренды по названию

Популярные бренды

Volvo Penta D1 Series, Руководство оператора

Результаты поиска

Содержание D1 Series

Отзывы:

Похожие инструкции для D1 Series

Бренды по названию

Популярные бренды