Volvo Penta D1 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 92

background image

Instruments and Controls

This chapter describes the instruments, panels and controls Volvo Penta sells for your engine.
If you would like to complement your instrumentation, or if your boat is equipped with instruments not described
here, we ask that you contact your Volvo Penta dealer.

Ignition Lock

The system lacks a start lock. Therefore, the helm
station should be lockable, or alternatively a lockable
main switch should be fitted, to prevent unauthorized
engine start.

Start/Stop Panel

Control Panel

On/Off button (1)

Depress the button to start or stop the system.
The panel cannot be switched off when the engine is
running.

Start button (4)

When the button is depressed the pre-heat function is
activated and the start motor engaged.

Multi-function button (2)

•

Confirm the alarm. If an alarm occurs, a flashing
warning symbol will be displayed in the tachometer
window and an audible alarm will sound.
The alarm is confirmed by depressing the multi-
function button. The audible alarm is silenced and
the warning symbol is lit continuously until the fault
is remedied.

•

Backlighting. To switch tachometer window
backlighting on or off, depress the button for 1 - 5
seconds.
The backlighting can be adjusted in five steps by
depressing the button for less than 1 second.

•

Adjust the tachometer window contrast by holding
down the button for more than 5 seconds.

Stop button (3)

The engine stops running when the button is
depressed.

22

47711262 01-2019 © AB VOLVO PENTA

«
...
22
23
24
25
26
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов

Похожие инструкции для D1 Series

Бренд: Jeanneau Страницы: 80

Бренд: feelfree Страницы: 8

Бренд: LITEBOAT Страницы: 28

Бренд: Grady-White Boats Страницы: 80

Бренд: Grady-White Boats Страницы: 74

Бренд: BRIG Страницы: 36

Бренд: Everglades Страницы: 148

Бренд: J/Boats Страницы: 36

Бренд: Rondar Страницы: 16

Бренд: Rondar Raceboats Limited Страницы: 14

Бренд: Pakboats Страницы: 7

Бренд: Ockelbo Страницы: 70

Бренд: Quantum Страницы: 32

Бренд: Jeanneau Страницы: 150

Бренд: Jeanneau Страницы: 115

Бренд: HOMCOM Страницы: 3

WaveRunner VX 2018

Бренд: Yamaha Страницы: 108

Бренд: CORRECT CRAFT Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды