Legal notice
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© copyright 2013 by conrad Electronic SE
c) charging a mobile device
1. Connect the Micro USB plug to your mobile device’s Micro USB connection. Alternatively,
you can connect another mobile device (such as an iPod/iPhone) using an appropriate
USB cable which might be available already. A complete recharge might not be possible for
all devices.
2. Connect the USB plug to the USB output 5.3V/Dc 1000mA located on the side of the
product. When charging a mobile device, 2 of the powerbank’s LEDs flash in the form of a
minus sign.
3. Push the battery key
located on the side of the product to check the internal
rechargeable battery’s charge status. The charge status is shown for approx. 3 seconds.
Then the minus sign continues blinking.
4. If you wish to interrupt charging without disconnecting the cable from the device, push and
hold the battery key
for approx. 3 seconds. The powerbank’s LEDs go out. Push and
hold the battery key for approx. 3 seconds again to continue charging.
5. Monitor the charging process. As soon as the mobile device is fully charged, the product
turns off automatically.
6. Disconnect the USB cable from the product and your mobile device when charging is
finished.
The product does not turn off automatically once the mobile device is fully charged if the
device being charged is used during charging.
If the product turns off due to internal short-circuiting, you can reset the product by
pushing and holding the battery key
for approx. 5 seconds. This reactivates the
product.
cLEANING AND mAINTENANcE
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical
solutions as they can cause damage to the housing and malfunctioning.
• Disconnect the USB cable and connected devices before cleaning the product.
• Never submerge the product in water.
• There are no components located inside the product you need to maintain. Never open/
dismantle the product.
• To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much
pressure to the housing to prevent scratching.
• You can easily remove dust using a long-haired, soft and clean brush.
DISPOSAL
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
The built-in rechargeable battery must be disposed of by a specialist.
b) Rechargeable batteries
You as the end user are required by law (Battery Ordinance) to return all used rechargeable
batteries. Disposing of them in the household waste is prohibited.
Contaminated rechargeable batteries are labelled with this symbol to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals
involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on rechargeable
batteries, e.g. below the trash icon on the left).
Used rechargeable batteries can be returned to collection points in your
municipality, our stores or wherever rechargeable batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TEchNIcAL DATA
Input voltage / current ........................... 5 V/DC, max. 500 mA
Output voltage / current ........................ 5.3 V/DC, max. 1000 mA
Internal rechargeable battery ................ Lithium polymer (LiPo) / 2000 mAh
LED ....................................................... 4 LED, blue
USB cable length .................................. approx. 0.6 m
Operating conditions ............................. -10 to +45 ºC, 0 – 90 % RH (non-condensing)
Storage conditions ................................ -10 to +45 ºC, 0 – 90 % RH (non-condensing)
Dimensions (W x H x D) ....................... 68 x 20 x 68 mm
Weight .................................................. approx. 72 g
