Volkswagen CJDA Скачать руководство пользователя страница 490

Страница: 490 / 553

Attachment of “battery positive wire” to alternator

Special tools and workshop equipment required

◆

Torque wrench (5…50 Nm) -V.A.G 1331-

Note

The threaded connection for the positive wire on the alternator
is labelled with “B1+”.

Caution

If the battery positive wire is not tightened to the specified
torque, there is a risk of the following:

◆

The battery will not be charged fully.

◆

Total failure of electrical system/electronics.

◆

Danger of fires from sparks

◆

Damage to electronic components and control units due
to excessive voltage

– With ignition switched off, disconnect earth strap from bat-

tery.

– Tighten securing nut of “B1+ wire” -arrow-. Specified torque:

15 Nm.

2.2

Checking alternator -C- and voltage reg-

ulator -C1-

Special tools and workshop equipment required

◆

Multimeter -V.A.G 1715-

◆

Auxiliary measuring set -V.A.G 1594 C-

Test prerequisites

● Fuses must be OK.

● Battery charged and tested.

● Earth connections OK

● Poly V-belt tension OK and alternator secured properly

● No faults must be stored in event memory

⇒

Page 26

, read

event memory.

Test procedure

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

474

Repair Group 27 - Starter, current supply, CCS

Содержание CJDA










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CJDA

Отзывы:

Похожие инструкции для CJDA

Бренды по названию

Популярные бренды

Volkswagen CJDA, Руководство по ремонту

Результаты поиска

Содержание CJDA

Отзывы:

Похожие инструкции для CJDA

Бренды по названию

Популярные бренды