manualshive.com logo in svg

VNS Therapy SENTIVA M2000 Wand, Техническое руководство

Поделиться
Скачать
VNS Therapy SENTIVA M2000 Wand Скачать руководство пользователя страница 73

73

Patient Does Not Perceive AutoStim 

Activation

•  Possible causes:
     -  AutoStim Threshold is too high (e.g., 70% threshold versus 50%)
     -  Patient has become accustomed to the programmed setting
     -  AutoStim output current is programmed to 0 mA
     -  Generator battery at end of service (EOS)
     -  Defective generator or lead
     -  Disabled generator

“Cannot feel AutoStim”

Interrogate the generator

Record the CAUSE

“The generator is currently disabled 

due to [CAUSE]. The generator is 

NOT supplying stimulation.”

Note: If the CAUSE is “a wand 

reset” and the reset was intended, 

continue with the session

• Confirm Detection is enabled

• Confirm AutoStim output current is set to > 0 mA  

   and 

≥

 Normal output current

Confirm heartbeat detection (See “Troubleshooting” in 

the programming system Physician’s Manual

Perform an AutoStim Diagnostics and record results

• Examine office visit data in Device History or Events

• Investigate consecutive office visits to identify any    

   changes in the average number of AutoStims per day  

   delivered

Yes

Current Delivered

If > 0

If 0

Current Not 

Delivered

No

“Disabled Message?”

Patient Report

The generator is delivering 

AutoStim. If perceived 

stimulation is desired, 

consider raising the 

AutoStim current

Re-evaluate at next office visit

If the average number of AutoStim activations per day 

since last office visit is 0 and the patient has had seizures 

during this period, adjust the AutoStim Threshold setting 

toward 20%

Repeat this process at subsequent office visits until the 

patient perceives stimulation or the device confirms the 

logging of events

Note: Decreasing the detection threshold increases 

the likelihood of detecting heart rate rises associated 

with seizures, but may increase the overall number of 

AutoStims delivered and impact battery longevity

Contact Clinical Technical Support

Содержание SENTIVA M2000 Wand


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды