Vmetro M5210RP-EFF Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 130

Vmetro M5210RP-EFF Скачать руководство пользователя страница 80

66

M5000 Series: User Guide

Issued June 20, 2007

Miscellaneous Functions

7.3 Interrupt Routing

In order to support a flexible interrupt routing mechanism, all interrupt source and destination
signals are routed to a PLD which provides the actual routing between sources and destinations:

FIGURE 7-1

Interrupt

Routing

The following devices are considered as possible interrupt sources:

•

2 PPMC sites (4 interrupt lines A,B,C and D)

•

Mezzanine PMC sites (4 interrupt lines A,B,C and D)

•

TUNDRA Universe IID VME-to-PCI bridge (2 interrupt lines i0 and i1)

•

Intel LXT9785 Fast Ethernet controller (1 interrupt line E0)

•

AMCC 440GX PowerPC processor (1 interrupt line X)

•

3 PCI6540 PCIX-to-PCIX bridges (2 interrupt lines P and S)

•

ISP2312 PCIX-to-Dual FC Host Adapter (2 interrupt lines A and B)

•

MERCURY PXB++ PCI-to-Race++ Bridge (4 interrupt lines A,B,C and D)

The following devices are considered as possible interrupt destinations:

•

PPMC#1 site (4 interrupt lines A,B,C and D)

•

AMCC 440GX PowerPC processor (16 interrupt lines P0 to P15)

•

Universe PCI-to-VME bridge

The following routing tables show the current interrupt mapping:

Interrupt Routing

CPLD

PowerPC

Processor

P0..P15

X

PowerPC

Processor

P0..P15

X

Dual FC

Host Adapter

A,B

Dual FC

Host Adapter

A,B

PCI-to-VME

Bridge

i2..i7

i0,i1

PCI-to-VME

Bridge

i2..i7

i0,i1

PCI-to-RACE++

Bridge

A,B,
C,D

PCI-to-RACE++

Bridge

A,B,
C,D

PCIX-to-PCIX

Bridge

P,S

PCIX-to-PCIX

Bridge

P,S

PMC

A,B,
C,D

PMC

A,B,
C,D

Ethernet

E0

Ethernet

E0

MEZZ

A,B,
C,D

MEZZ

A,B,
C,D

PMC

A,B,
C,D

PMC

A,B,
C,D

«
...
78
79
80
81
82
...
»

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов