manualshive.com logo in svg

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 66 / 130

Поделиться
Скачать
Vmetro M5210RP-EFF Скачать руководство пользователя страница 66

52

M5000 Series: User Guide

Issued June 20, 2007 

Mezzanine PMC Carrier

6.3 Installing PMC Modules onto the PMC Carrier

The M5000 is shipped with two PMC filler panels mounted in the front panel. They act as EMC 
shielding in unused PMC positions. Before installing a PMC module, the filler panel(s) must be 
removed. This is done by pushing them out from the backside of the front panel

Step 1: Remove the Mezzanine PMC Carrier board from the M52xx. 

1.

Remove the four screws that attach the PMC Carrier board to the M52xx board. These screws 
are removed from the rear of the M52xx board. See Figure 6-3

2.

Carefully remove the PMC Carrier board from the M52xx.

Warning! 

Be extremely careful when inserting screws to secure PMC modules. 

Touching component leads, or the printed circuit board itself, with a screwdriver may 
cause permanent damage to the board

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов