Vmetro M5210RP-EFF Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 130

Vmetro M5210RP-EFF Скачать руководство пользователя страница 36

22

M5000 Series: User Guide

Issued June 20, 2007

Installation and Hardware description

Fibre Channel Port LEDS

RS232 Connector and cables

The processor has its own dedicated serial connections. The serial connections are intended for
application development, test and debug purposes. The Rx and Tx signals from each UART are
available in the front panel connector. The pinout of this connector depends on the model of your
M5000.

Different converter cables exist for connecting standard 9-pin D-SUB cables to the non-standard
M5000 Mini-DIN connector:

•

601-M5x10-PC-RS232 cable has a single 9-pin D-SUB that connects to the #1 UART. This
cable is crossed and is the standard cable shipped with standard models.

•

601-M5x10-2xRS232 split cable has two 9-pin D-SUBs. The D-SUB on the short cable end
connects to the first serial port on the #1 UART. The D-SUB on the long cable end connects to
the second serial port on the #2 UART. Available on request.

•

601-M5x10-RS232/RS422 split cable has two 9-pin D-SUBs. One connects to the #1UART.
The other connects to the #2UART with RS422 signalling (housing is colored red). This cable is
provided with models M5x10(RP)-xxx4.

TABLE 2-12.

Fibre Channel Port LEDS

Amber LED

Green LED

Power On

On Steady

On Steady

Loss of Sync

Flash at half-second interavls

OFF

Signal Acquired

On Steady

OFF

Online

OFF

On Steady

System Error (8002h)

Flash at half-second intervals

Flash at half-second intervals

«
...
34
35
36
37
38
...
»

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов