Vmetro M5210RP-EFF Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 130

Vmetro M5210RP-EFF Скачать руководство пользователя страница 16

2

M5000 Series: User Guide

Issued June 20, 2007

Product Overview

1.1 Main features:

•

A PowerPC processor subsystem (440GX from IBM) with up to 256MiB local DDR-SDRAM
memory, 32MiB of FLASH memory, four Ethernet ports (two 10/100/1000Mbps and two 10/
100Mbps) and two serial ports.

•

Two standard PPMC sites located on separate PCI segments (64-bit, 33/66MHz PCI, 66/100/
133MHz PCI-X). In addition, PMC#1 can be MONARCH

•

Dual 2Gib Fibre Channel I/O Controller (ISP2312 from QLOGIC) (Optical)

•

Single 10/100 Ethernet port (front panel connector)

•

Dual serial ports configurable as two RS-232 ports or one RS-232 and one RS-422

•

PCI-to-VME bridge (Universe IID from Tundra)

•

Three PCI(X)-to-PCI(X) bridges which connects the different PCI(-X) segments together
(PCI6540 from PLX)

•

Optional PCI-to-RACEway bridge (PXB++ from Mercury)

•

Optional I/O Spacer extension via a built-in connector, thus adding up to 3 Ethernet ports (One
Fast Ethernet 10/100 SMII and two Gigabit Ethernet 10/100/1000 RGMII) and an I2C bus.
Note: Adding more than one Gigabit Ethernet port will reduce the number of Fibre Channel
ports

•

Optional mezzanine extension via a built-in connector, thus adding 3 PMC sites to the
Quaternary PCI segment. These PMC sites are 64-bit, 33MHz PCI, 5V signaling.

•

One PIM I/O board slot, in accordance to VITA36.

FIGURE 1-1

Component

Overview

P2

P1

PMC #2

PMC #1

PXB++

(Optional)

Universe IID

P0

P2P

P2P

MEZZ

ISP 2312

SFF

SFF

DDR

SDRAM

RJ45

GbE

VMEbus

VMEbus

Power PC

IBM 440GX

Primary PCI

segment

Secondary PCI

segment

Tertiary PCI

segment

Quaternary PCI segment

Two 64/100 MHz PCI-X

PMC sites (PrPMC)

Dual 2 Gb/s on-board

Fibre Channel

I/O spacer extension adding
2Gb/s Ethernet ports and/or

x500MEZZ for additional 3

PMC slots (64/33MHz)

3 PCi-X to PCI-X bridges

allowing 3 PCI-X segments

and 1 64/33 MHz PCI

segment

Optional PCI to

RACEway bridge

(PXB++)

Differentially routed

P2-IO and P0-IO for

high speed signalling

(Starfabric)

P2P

«
...
14
15
16
17
18
...
»

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов