background image

 

 

VXO8330/4114B 

INSTALLATION GUIDE

 
 

 

PAGE 1 of 6

 

BEFORE BEGINNING YOUR INSTALLATION 

Read through the instruction guide before getting started with the installation. Professional installation is recommended for 
this product. 
 

 

 

CONTENTS

 

  Quad Trumpet Train Air Horn (Black) 

  200 PSI Air Compressor 

  3 Gallon Air Tank 

  12V Electric Air Valve (Solenoid) 

  240 PSI Air Pressure Gauge 

  170-200 PSI Pressure Switch 

  250 PSI Safety Valve 

  1/4" NPT Wing Style Drain Valve 

  1/4" NPT Compression Fitting for 1/4" OD Air Line 

  1/4" NPT Hex Head Male Plug 

  1/2" NPT Hex Head Male Plug 

  1/4" OD Nylon Plastic Hose (6 Feet) 

  12mm Thread Sealant Tape (16 Feet) 

  30A In-line Fuse with Waterproof Holder 

  Remote Mount Air Filter 

  Horn Button 

  Mounting Hardware 

 

 

 

SAFETY INSTRUCTIONS 

  Do not attempt to disassemble, repair or customize this product. 

  Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. 

  Avoid reaching out to touch or pick up any fallen or water submerged parts. 

  Never leave this product unattended during use. 

  Intended for use by adults only. 

The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC 
power source of 12 volts. 

Содержание VXO8330/4114B







Отзывы: