Vivotek SD9363-EHL Скачать руководство пользователя

Страница: 82 / 332

VIVOTEK

User's Manual - 82

Network > DDNS

This section explains how to configure the dynamic domain name service for the Network

Camera. DDNS is a service that allows your Network Camera, especially when assigned with a

dynamic IP address, to have a fixed host and domain name.

Express link

Express Link is a free service provided by VIVOTEK server, which allows users to register a

domain name for a network device. One URL can only be mapped to one MAC address. This

service will examine if the host name is valid and automatically open a port on your router. If

using DDNS, the user has to manually configure UPnP port forwarding. Express Link is more

convenient and easier to set up.

Please follow the steps below to enable Express Link:

1. Make sure that your router supports UPnP port forwarding and it is activated.

2. Check

Enable express link

3. Enter a host name for the network device and click

Save

. If the host name has been used by another

device, a warning message will show up. If the host name is valid, it will display a message as shown

below.

https://vivotek_test3454.2bthere.net

2010/12/10 17:08:56

Содержание SD9363-EHL













































































































































































































































































































































Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды

Vivotek SD9363-EHL, Руководство пользователя

Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды