Vivotek SD9363-EHL Скачать руководство пользователя

Страница: 127 / 332

VIVOTEK

127 - User's Manual

Applications > DI and DO

Digital input

: Select High or Low to define normal status for the digital input. Connect a digital input from

a sensor device to the camera, the Network Camera will report the current signal status. You may then

configure the Normal status (non-trigger status) as High or Low.

Digital output

: Select High or Low to define normal status for the digital output. Connect an output line to

an external device, the Network Camera will report the current signal status. You may then configure the

Normal status (non-trigger status) as High or Low.

Set up the event source as DI on

Event > Event settings > Trigger.

Please refer to page 110 for

detailed information.

Содержание SD9363-EHL













































































































































































































































































































































Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды

Vivotek SD9363-EHL, Руководство пользователя

Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды