Vivotek SD9363-EHL Скачать руководство пользователя

Страница: 101 / 332

VIVOTEK

101 - User's Manual

PTZ > PTZ settings

This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. The

camera comes with built-in PTZ mechanisms.

Home location settings

Move your current field of view to a preferred location using the PTZ panel or mouse clicks

on the screen, and use the below buttons to configure the current view as the default home

position. You can also restore the home posiotion to the factory default, which is approximately

45 degree looking down with the lens lined up with the VIVOTEK logo.

Patrol list

This column displays the configured patrols. Note that only one patrol can apply at a time. Use

the ON/OFF buttons to enable/disable an existing patrol.

Use the buttons below to create a

recorded patro

l or a

preset patrol

Содержание SD9363-EHL













































































































































































































































































































































Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды

Vivotek SD9363-EHL, Руководство пользователя

Результаты поиска

Содержание SD9363-EHL

Отзывы:

Похожие инструкции для SD9363-EHL

Бренды по названию

Популярные бренды