VivoLink VL12K12-BULK1V-EU-4K Скачать руководство пользователя страница 11

Страница: 11 / 35

Multi-function AV Distribution System

⑫

PoC IN/HDBT OUT:

RJ45 port to connect the

HDBT IN/PoC

port of receiver by

CATx cable. The transmitter can be powered by this port once the receiver has

been powered up.

⑬

FIRMWARE:

Micro-USB port for firmware upgrade.

3.2 K12-RX1-4K Receiver

①

FIRMWARE:

Micro-USB port for firmware upgrade.

②

LED indicators:



ON:

The LED illuminates green when the system is in normal working status.



LINK:

The LED illuminates green when there is a valid HDBaseT connection

with the transmitter. The LED is off when there is no valid link.



HDCP:

The LED illuminates green when there is HDMI video traffic with HDCP.

It will blink green when there is HDMI video traffic without HDCP and will be off
when there is no HDMI video traffic.

③

POWER LED:

The LED illuminates red when power is applied.

④

TCP/IP:

RJ45 port to connect the control device (e.g. PC) to control the system by

GUI.

⑤

HDBT IN/PoC:

RJ45 port to connect the

PoC IN/HDBT OUT

port of transmitter by

CATx cable.

⑥

TO DISPLAY:

Type-A female HDMI output port to connect a display device (e.g.

Projector).

HDBT IN/PoC

TO DISPLAY

LINE OUT

IR OUT

DC 24V

TCP/IP

TOUCHSCREEN

FROM

RS232

OUTPUT

CONTROL

MIC

NETWORK

INPUT

MIC

2x20Watt

MIC

LINE

REMOTE

MUTE

AUDIO

LINK

HDCP

FIRMWARE

10 11

Содержание VL12K12-BULK1V-EU-4K



































Результаты поиска

Содержание VL12K12-BULK1V-EU-4K

Отзывы:

Похожие инструкции для VL12K12-BULK1V-EU-4K

Бренды по названию

Популярные бренды

VivoLink VL12K12-BULK1V-EU-4K, Руководство пользователя

Результаты поиска

Содержание VL12K12-BULK1V-EU-4K

Отзывы:

Похожие инструкции для VL12K12-BULK1V-EU-4K

Бренды по названию

Популярные бренды