Vivitek DK10000Z страница 7 Скачать руководство пользователя

Страница: 7 / 62

DK10000Z Series DLP Projector - User Manual

UM100000823EN03

Installation and Use Notices

1. Read and keep this manual properly.

2. Pay attention to all the noted warnings, and follow all the guidelines and descriptions in this manual.

3. Do not use the projector near water.

Do not install the equipment near the thermal sources, such as heaters, radiators, furnace, amplifiers, and any

other equipment that may generate heat.

5. Be careful while holding the equipment or moving the trolley with projector to prevent the equipment from turning

over.

Notice whether there is any parts with flaws after receiving the projector.

Please notice that the projector will not power on until the lens is fitted. The protection covering the lens should

be taken to install the lens.

8. Do not let any vent be obstructed.

Wide blade

Narro

w blade

Groun

ding blade

9. Do not destroy the safety protection function of polarized or grounding plug of power cord.

A polarized plug has one wide and one narrow blade. The plug has two blades and one

grounding blade. The wide blade or grounding blade is provided for the safety concerns.

If the plug provided does not match the outlet, please contact the electrician to change

outlet.

10. The +12V trigger only outputs 12V DC trigger signal. Do not connect other power input or

output. Otherwise, the equipment may malfunction.

TRIGGER

11.

Adjust the slide switch with suitable volt input, and then plug in the projector; the red LED indicator would flash

and then stabilize, getting into standby mode. User should only use the connectors or accessories provided by

the manufacturer. Please refer to "Selecting the Input Voltage of AC Power on page20 ".

12.

When user turns on the projector, the red LED indicator would flash until stabilize.

Do not look at the lens directly while the projector is running.

RG2

CAUTION: Do not look into the lens

13. Install or use the projector, please do not look directly into the lens or the lens

light output. The glare after focusing may cause damage to your eyes.

14. Unplug the power cord of the equipment if there is a thunderstorm or the equip-

ment is not going to be used for a long time.

15. The packaging materials can be kept properly for transportation use afterwards.

16.

If any breakdown occurs, please contact dealer or manufacture for qualified

repair service.

Disposal of Old Electric and Electronic Equipment

The symbol on your product or the package represents that the product should not be treated as the normal

household waste when discarded but should be carried to the recycling location of the waste electric and

electronic equipment. The consequence on the environment and human health due to the incorrect disposal of

the product can be prevented if it can be ensured that the product is properly discarded. Material recycling is

helpful to the protection of natural resources. The symbol is only valid in European Union. If you want to discard

electrical and electronic equipment, contact the governmental authorities or your dealer for the correct method

of disposal.

Important Recycling Instructions

The product may contain other electronic wastes and may pose risk if not discarded properly. Abide by the local, state/

provincial or federal laws of recycling or discarding. For more information, please visit the website and contact Elec-

tronic Industries Alliance (EIA) on WWW.EIAE.ORG.

Содержание DK10000Z































































Результаты поиска

Содержание DK10000Z

Отзывы:

Похожие инструкции для DK10000Z

Бренды по названию

Популярные бренды

Vivitek DK10000Z, Руководство пользователя

Результаты поиска

Содержание DK10000Z

Отзывы:

Похожие инструкции для DK10000Z

Бренды по названию

Популярные бренды