background image

VITEK

VITEK

FEATURES

• 1/2.5” 8.0 Megapixel Progressive Scan CMOS image 

sensor

• Up to 30fps live view @ 8 MegaPixel (3840x2160)
• Motorized 3.3-12mm Varifocal Lens
• 30 Infrared LED’s with 100’ IR Range 
• 120dB Super Wide Dynamic Range (WDR)
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction 
• Fully Programmable Intelligent Analytics including Object 

Removal/Museum Search, Line Crossing, and Area 

Intrusion Detection

• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• Remote Viewing via CMS, Internet Explorer, and iOS & 

Android Apps

• IP66 Weather Resistance & IK10 Impact Rating
• MicroSD memory card slot for Local recording supporting 

up to 128GB MicroSDXC cards

• ONVIF Compliant
• Optional Wall (VT-TWM03) & Junction Box (VT-TJB02) 

Mounts Available

• 12VDC & PoE (Power over Ethernet) Operation

 VTD-TND8RMS

Transcendent Series 8 

Megapixel H.265 Indoor/

Outdoor WDR IP Dome Camera 

with 30 IR LED Illumination & 

Motorized Varifocal Lens

QUICK START GUIDE

PLEASE NOTE: 

Complete User Guide, Software, Tools, and Updates are 

available online.  Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

Содержание Transcendent VTD-TND8RMS









Отзывы: