visual engineering DTC TM-RX Скачать руководство пользователя страница 8

Страница: 8 / 45

TM-RX Receiver

May 2021

Visual Engineering

Video solutions. Integrated

visualengineering.co.uk

Page 8

The battery is the VE SLI-50 with a 48Wh capacity, which

is used to power the TM-RX. It can be used in either

orientation to simplify battery changes.

The battery incorporates a gas gauge circuit which

accurately measures the power in and out of the cell,

providing an accurate time remaining indicator, both

under charge and discharge conditions.

To check the power remaining in the battery simply press

the indicator button to get the power level to display on

the LED power level meter for several seconds.

The Battery

Indicator Button

LED Power

Level Meter

Battery Insertion

Open the battery hatch by releasing the locking

mechanism as indicated in the image on the

right.

Battery

Insertion

Release Battery Latch

Insert the battery into the open battery hatch

with the LED indicator facing outwards, as

shown.

It is possible to insert the battery in either

orientation, with the indicator button on the

right or the left.

Push the battery home, close the battery hatch

door and secure the battery latch.

The battery being inserted on the right is

showing its remaining charge on its power level

meter as the indicator button has recently been

pressed.

Note

: An extra internal backup battery allows the main battery to be hot swapped without any

interruption to its operation. The internal battery will support unit power for 15 seconds to allow

the battery swap to be completed.

Содержание DTC TM-RX














































Результаты поиска

Содержание DTC TM-RX

Отзывы:

Похожие инструкции для DTC TM-RX

Бренды по названию

Популярные бренды

visual engineering DTC TM-RX, Руководство пользователя

Результаты поиска

Содержание DTC TM-RX

Отзывы:

Похожие инструкции для DTC TM-RX

Бренды по названию

Популярные бренды