manualshive.com logo in svg

Vislink UltraReceiver, Руководство пользователя

Поделиться
Скачать
Vislink UltraReceiver Скачать руководство пользователя страница 39

 

UltraReceiver User Manual 

 

Receiver Setup 

 

 

Issue No: 3 

Page: 33 

 
Ref: ULRX-ASUM-700X 

 

Copyright © 2018 Vislink plc 

 

To send video over IP between two units with a direct Ethernet connection, do the 
following: 

1.

 

In the receiving device, set the IP address of the IP block (or leave as default), under 
IP Video Setup. The Mask and Gateway are only necessary if the traffic is going to 
pass over a network. 

2.

 

In the receiving device, set the IP Port to the required value (or leave as default). 

3.

 

In the sending device, set the Destination IP Address (under ASI to IP) to the value set 
in step 1. 

4.

 

In the sending device, set the Destination Port to the value set in step 2. 

5.

 

In the sending device, set the source of the IP block as required (either Demodulator 
or ASI Input). 

6.

 

In the receiving device, set the destination of the IP block as required (either Decoder 
or ASI output). 

On the receiving device, status can be monitored on the IP Video Setup page. The steps 
above are similar when using other devices at either end of the link. If a network is being 
used, then ensure that all the IP addresses on the network are unique, and that they all 
have the same subnet mask. 

 

The receiver can provide various decryption options depending on the license options for 
the unit. 

First, the required decryption algorithm is selected and the appropriate key is then 
entered, either from the front panel or via Link Control software running on a PC.  

For the AES keys these must be entered in two (AES128) or four (AES256) 8-byte segments. 

The BISS-1, BISS-E and AES+ decryption will only decode an encrypted stream; EBS and AES 
will decode non-encrypted (clear) streams and also the appropriately encrypted streams. 

 

This option allows for the use of third party down convertors with the L217x receiver. 

The user must first select a down convertor of the Other type in the Demod > 
Downconverter menu, then select the required LO frequency and polarity. These can be 
set individually for each of the RF inputs. These can then be stored as any one of the Config 
memories to be re-loaded as required. 

 

 

 

Содержание UltraReceiver











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды