manualshive.com logo in svg

Vislink IRD6200, Руководство пользователя

Поделиться
Скачать
Vislink IRD6200 Скачать руководство пользователя страница 21

 

IRD6200 IRD User Manual 

 

Main Display 

 

 
Issue No: 1 

Page: 15 

 
Ref: IRD6-ASUM-700X 

 

Copyright © 2019 Vislink Technologies, Inc. 

4.3.5.

 

Time 

Set unit Time and Date, and display the accumulated run-time of the unit in 
hours. 

4.4.

 

Support Menu 

The Support menus display useful information. This information helps if you need 
to contact Vislink. In particular, the versions of the various modules in the unit. 

4.4.1.

 

Diagnostics 

Use this menu to for unit information, such as internal temperatures. 

4.5.

 

Menu Overview 

The below table shows the entire menu structure for your IR6200 IRD unit. Your 
system may not display all menu options. Some menu options are context 
sensitive, depending on your current configuration. Some menu options may be 
license dependent. 

NOTE: When “..” shows in between two values, it indicates the value available. 

For instance, “Service 1..4” means there are four services to select from.

 

4.6.

 

Webserver Operation over RJ45 Port 

The receiver has a 10/100M Ethernet port (see Section 2.13.8) that can connect 
to any standard Ethernet network using a standard or crossover Ethernet cable. 

4.6.1.

 

How Do I Set Up a Basic Connection? 

To make individual IRD6200 configuration easier, access the inbuilt menu system 
using the integrated webserver. Use the following procedure to connect to the 
webserver over the RJ45 network port: 

1.

 

Power up the unit and wait for the unit to fully boot. 

2.

 

Connect the unit to a PC running a web browser, either directly, using an 
RJ45 network cable or via a router. 

NOTE: Depending on the age of your PC, you may require a crossover RJ45 

cable. In most cases, modern PCs and routers include auto-switching 
(Auto MDIX) so either type of RJ45 cable are suitable. 

3.

 

If you wish to use non-default settings, configure the IP addresses from the 
front control panel: 

a.

 

MAIN MENU > UNIT SETUP > CONTROL 

b.

 

Configure the IP address and Subnet Mask and press Enter each time to save: 

NOTE: The below values are default values. 

NOTE: The network port only supports static IP addressing. 

 

IP address:    

192.168.000.90 

 

Subnet mask:  

255.255.255.000 

 

Gateway:    

192.168.000.001 

4.

 

If using the default settings, modify the network settings of your PC to use 
the same subnet mask and an address from the same subnet e.g.: 

 

PC IP Address:  

192.168.000.100 

 

PC subnet mask:   255.255.255.000 

Содержание IRD6200

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды