Operation
1.
Power-on Mode:
1) Install the battery into the module 2) Close the bracket 3) the
detector will take 8 to 12 sec. and emit a beep to confirm and start the burglar
system. The detector will alarm once remove the bracket.
2.
STANDBY MODE:
The red LED, as the ALARM indicator, are featured with the
smoke alarm. It can be seen through the clear test button on the cover of the unit.
When red LED flashes once 334 seconds, it indicates the smoke alarm is under
normal operation. When smoke alarm senses smoke and simultaneously sounds
an audible alarm with 3 beeps, pause and 3 beeps. The red LED will flash
continuously and rapidly.
3.
SILENCE FEATURE:
The silence feature can temporarily quite an alarm for up to
10 minutes. To use this feature, press test button on the cover when it alarms.
However, if the smoke concentration around the smoke alarm unit is still at alarming
level after 10 minutes of silence, the unit will re-alarm immediately.
4.
LOW BATTERY WARNING SIGNAL:
If the alarm horn begins to chirp once in 43
seconds with red and yellow LED flashing, this signal means that the smoke alarm’s
battery is weak. This low battery warning signal should last for up to 30 days, but
you should replace the battery immediately to secure your protection.
5.
TAMPER SWITCH FEATURE:
If the smoke alarm is not mounted into the bracket
properly within 5 minutes after battery is installed, the tamper function is triggered
and the Yellow LED is steadily on. If the smoke alarm is still not mounted into the
bracket properly 5 minutes after battery is installed, you will hear temporal three
sound with yellow LED steadily on until smoke alarm is mounted back into bracket
properly.
6.
MALFUNCTION (ERROR) SIGNAL:
If you hear 3 “beep” with yellow LED flashing
3 times in 43 seconds, it indicates that the smoke alarm does not work properly,
please have it repaired or serviced.
7.
TESTING YOUR SMOKE ALARM
Test the alarm weekly by pushing firmly on the
test button with your finger for around 4 seconds until the horn sounds, the sound
pattern is 3 beeps , pause, and then 3 beeps with red LED flashing continuously
and rapidly.If the smoke alarm beeps three with yellow LED flashing three times in
43 seconds, it indicates the smoke alarm is not working properly, it requires to be
repaired or serviced
.
Then, the smoke detector will send an alarm report (Alarm
type: 0x01, Level: 0xFF) to the user’s controller and also the dectecor will send an
alarm report (Alarm type: 0x01, Level: 0x00) while the alarm off.
8.
Battery Power indicator:
The detector will report the current status of battery
capacity to the user
’s contorller.
9.
Self-Protection Mode:
If the detector removed from bracket, the detector will send
an alarm sensor (Alarm type:0x01, level:0xFF) to the Z-Wave Interface Controller ,
and the Yellow LED will on contiuously and the detector will sound.
Federal Communications Commission Statement
This equipment has been followed to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
and correct the interferene by one of the following measures:
-- Reorient or relocate the receiving antenna,
-- Increase the separation between the equipment and receiver,
-- Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undersired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user
’s authority to operate this equipment
.
Limited Warranty
Vision Guarantees that every wireless smoke detector is free from physical defects in
material and workmanship under normal use for one year from the date of purchase. If
the product proves defective during this one-year warranty period, Vision will replace it
free of charge. Vision does not issue any refunds. This warranty is extended to the
original end user purchase only and is not transferable. This warranty does not apply to:
(1) damage to units caused by accident, dropping or abuse in handling, or any negligent
use; (2) units which have been subject to unauthorized repair, opened, taken apart, or
otherwise modified; (3) units not used in accordance with instruction; (4) damages
exceeding the cost of the product; (5) transit damage, initial installation costs, removal
cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw