Vision & Control Vicosys 5400 Скачать руководство пользователя страница 53

Страница: 53 / 64

vicosys

5400

Commissioning

999.994.729.10-en-2.3

6.3.9 Connecting and switching on the operating voltage

NOTICE

Destruction caused by potential differences.

•

Ensure that the device is properly grounded (equipotential bonding).

Connect the operating voltage

The operating voltage is supplied via the 3-pin operating voltage connector

(scope of delivery) on the device.

CAN 2

CAN 1 / Serial 2

LED

CAN 1

CAN 2

LED

- R

CFAST

HD PWR

RST PWR

I/O

GND

Image 21: Operating voltage connector

(1)

Operating voltage connector

1. Ensure that the power supply is switched off.
2. Unscrew the operating voltage connector from the device.
3. Connect the positive voltage (plus) to +V

and the negative voltage

(ground) to GND.

Pin

Signal

Description

+ V

Operating voltage

Do not use

GND

Ground

4. Plug the operating voltage connector to the device and tighten the screws.

Содержание Vicosys 5400

































































Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды

Vision & Control Vicosys 5400, Инструкция по эксплуатации

Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды