ViscoTec Preeflow eco-CONTROL EC200-B Скачать руководство пользователя

Страница: 16 / 36

16 / 35

Version 1.9

eco-CONTROL EC200-B

Operation and maintenance instructions

Dosing by means of an external controller

As in the case of

dosing with the foot switch

, but the triggering and termination of the

dosing are done by supplying an electrical signal. See 8.3, Interfaces, page 34.

Note:

If a memory card is being used, press the foot switch briefly to load the saved and

most recently run program and to display it on the screen. Press the foot switch once

again to start the dosing. It behaves in exactly the same way with an external signal.

5.9

Calibrating

Preparation

• Connect to the controller the dispenser that has been made ready for operation and

bled.

Caution:

Only remove and insert the mains plug of a dispenser (plug 16, section 5.2,

Connections on page 11) once the power has been switched off. Otherwise the

electronics of the drive motor could be damaged.

• Keep at hand a suitable vessel (calibration vessel) to catch and measure the quantity

required for calibration.

5.9.1

Calibration auto

Note:

During the calibration operation the Dosing system cannot be operated by

either the foot switch or an external control signal.

• Press the

PRG

key,

system selection menu

display 2 appears.

• Select and confirm

Calibration auto

, the menu

Calibration

auto

, display 14 appears.

• Select * and confirm the desired flow rate

• Select the OK button and confirm, the next input dialog

appears (display 15).

* The flow rate (output of the dispenser) should correspond approximately to the flow

speed at which the dosing is to be done. The values 25%, 50% and 75% are offered

for selection. This setting compensates for a reduction in the level of efficiency

(depending on the medium) as the speed increases.

Start/stop
Time program
Calibration auto
Calibration manuel
Teach in function
Administration

Quantity program

10 47h

Fr 18.03.11

Service

Esc OK

Accept with OK

Esc

calibration auto

Flow rate

Press enter for change

middle

50%

Содержание Preeflow eco-CONTROL EC200-B





































Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды

ViscoTec Preeflow eco-CONTROL EC200-B, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды