VIPA TM-E 900-1E640 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 68

VIPA TM-E 900-1E640 Скачать руководство пользователя страница 20

Chapter 2 Hardware description

Manual VIPA TM-E

2-2

HB39E - TME - RE_900-1E640 - Rev. 09/11

Properties

The TM-E is an intelligent teleservice module. This module makes simple
and safe communication with your machines and plants possible via
telephone respectively internet. Values of your plant may be observed and
appropriate reactions to limit exceeds may be configured.
Here e.g. plant data may be collected and sent via mail.
Due to the integrated Web page, for configuration there is no additional
software necessary.
Due to the predefined server the embedding to a VIPA PLC may be
established problem-free. The TM-E module may be integrated as PG/OP
interface to the Siemens SIMATIC manager by means of a station file.

•

Transparent Ethernet-Gateway with TCP/IP Router

•

Sending alarms by E-Mail and SMS (only via Free-SMS-Provider)

•

up to 20 Ethernet sessions simultaneous

•

Programmable gateway by BASIC

•

fully customizable web pages (in HTML)

•

integrated alarm management

•

RS485 MPI interface

•

RJ45 Ethernet interface

•

RJ 11 PSTN modem (analog)

Type

Order number

Description

TM-E Analog

VIPA 900-1E640 DC 12 ... 24V, PSTN (Analog), MPI, Ethernet RJ45,

Router functions, DI 1xDC 24V, DO 1xDC 24V 0.2A

Overview

Properties

Order data

«
...
18
19
20
21
22
...
»

Содержание TM-E 900-1E640





































































Отзывы:

Нет отзывов